Wear-Tek® 4400 Commercial Concrete Sealer

A solvent-based, single-component, moisture cured aliphatic urethane coating, this specialty concrete coating produces a glossy, tough, hard-wearing, and chemically-resistant surface.

  • Coverage Up to 300 square feet
  • Coats 1
  • VOC Content 300 g/L
  • Finish Gloss
4400 Concrete Sealer Bucket Image

Project Calculator*

Wear-Tek 4400 Concrete Sealer marketing image


Wear-Tek® 4400 is a solvent based single component cyclo- aliphatic urethane coating. It produces a tough, glossy, hard- wearing and chemically resistant surface for the protection of concrete, wood and other approved substrates.

Wear-Tek® 4400 is available as a transparent, glossy coating or as a pigmented colored material that possesses excellent hydrolytic stability and ultra- violet radiation resistance as well as high tensile strength while accommodating movement.


Exceptional when used for:
  • Stadiums/Buildings
  • Balconies
  • Plazas
  • Bridge decks
  • Stairways/Walkways
  • Parking garages
  • Concrete, brick, masonry
  • Wood, metal, rubber, plastic composites



  • Composition: 48% solids nanotechnology driven high- performance moisture cure single component aliphatic urethane coating
  • May be used over concrete, wood and other approved substrates
  • Provides a long service life without loss of flexibility


  • Accommodates normal substrate movement and thermal stresses
  • High strength, tenacious adhesion to many surfaces
  • Maintains a cleanable, attractive, hygienic surface, easily scrubbed and cleaned
  • Increases friction to improve traction


  • Protects substrates from chemical attack and corrosion, withstands heavy use and environmental attack
  • Long term color retention, highly fade resistant
  • Penetrates into concrete surfaces to seal and waterproof floors, walls and decks, providing a solid clear or colored finish
  • Provides a tough color-fast finish on roof top decks and walkable metal roofs

Wear-Tek 4400 Rises Above

Wear-Tek 4400 meets or exceeds the following tests:

  • ASTM D-2240: Durometer Hardness
  • ASTM D-412: Tensile Strength
  • ASTM D-1044: Surface Abrasion
  • ASTM C-711: Flexibility
  • ASTM D-1474: Indentation Hardness
  • ASTM D-570-77: Water Absorption
  • ASTM G-23: Weathering

Abrasion/Chemical Resistance Percentage Improvement vs. Control

Low solids coating
Traditional coating
Leading brand coating
Other coating
Wear-Tek® 4400
Sealer Product

Auxilliary Information

  • Preparation

    1. The concrete substrate to be coated must be clean, dry, and completely free of loose particles, grease, oil, or any substance that would interfere with proper bond.
    2. Surface and air temperatures must be at least 35°F during application. Surface and air temperatures should not exceed 95°F. Keep material from freezing. Do not apply during inclement weather or when inclement weather is expected within 12 hours. Application must be protected from precipitation for at least 4 hours.
    3. Protect people, property, vehicles, window glass, roofing materials, plastic products, shrubbery, landscaping and all surfaces not set for treatment from overspray.
  • Application

    Wear-Tek® 4400 may be applied by brush or airless spray technique in a thin, even coat. Care should be taken to avoid creating foam or trapping air bubbles which may later result in pinholes or hazing. If traction enhancement is required, iron-free sharp white quartz sand or Soft Sand Rubber Granules may be broadcast onto the wet Wear- Tek® 4400. After the first coat has thoroughly dried with the embedded sand, a second coat of Wear-Tek® 4400 is applied to thoroughly encapsulate the aggregate. Sized and graded sharp white quartz sand and Sand Rubber Granules are available from KreteTek Industries Inc.

  • Application Notes

    Dry Time:

    Typical drying time for walking is 2 hours at 70°F and 50% relative humidity. Typical drying time for a full cure is 24 hours at 70°F and 50% relative humidity. Cooler temperatures or higher relative humidity can extend the drying time

    Clean Up:

    Clean equipment, tools and surfaces with xylene. Unused or old material may be disposed of in a waste disposal site in accordance with local, state and federal laws.


    Use appropriate safety equipment during application and handling. Please refer to the safety data sheet (SDS) for additional precautionary instructions before use.


    To repair damaged areas, coarse sanding should be followed by thorough cleaning with fresh water. Wear-Tek®4400 may then be reapplied to the clean, dry surface.

    Best Performance

    • Proper application is the responsibility of the user.
    • Make sure the most current versions of technical data sheets and safety data sheets are being used.
    • Keep out of reach of children and pets.
    • Store in a cool, dry place away from direct sunlight. Avoid opened containers, as moisture will cure the material.


    300 square feet per gallon. Variations in texture and porosity of substrate will affect the coverage and performance of the product.