- Feature: Densifier & hardener
- Chemistry: Lithium silicate
- Color: Clear
- Finish: Invisible
- Category: Penetrating
- Carrier: Water
- Availability: Ultra Concentrate: Makes 3 gallons if polishing concrete. Makes 4 gallons if priming concrete
- Packaging: 1 Gallon
- Coverage: Up to 1000 sq. ft. per coat
- Reconstitution Ratio: Polishing concrete: 1 part sealer : 2 parts water. Priming concrete: 1 part sealer : 3 parts water
- Interior/Exterior: Interior/Exterior
- Application Method: Sprayer, Roller
- Application Temperature: 45 F - 90 F
- Number of Coats: 1
- Drying Time (dry to touch): 6 Hours
- Drying time (full cure): 24 Hours
- Time before/after rain: 48 Hours
- New Concrete: Yes, at least 28 days after being poured
- Storage/Shelf Life: 1 Year
- Clean up: Soap/water
- Paintable: Yes
- VOC Content: 0 g/L
Lithi-Tek 4500 is an advanced, high performance, industrial strength, deep penetrating concrete sealer and densifier designed to strengthen concrete. This unique formula incorporates leading molecular nanotechnology. The subsequent chemical reaction elicited from the formula fills the pores and capillaries with an impenetrable crystallization. Lithi-Tek 4500 is a uniquely transparent formula containing a proprietary blend of enzymes and surfactants that aide in accelerating a deeper penetrating disbursement. Thus eliciting a more effective, uniformed chemical reaction between the formula and the concrete substrate it’s being applied to. Lithi-Tek 4500 treats and seals from the inside out; strengthening the concrete as well as providing a seal that will not chip, flake, delaminate or breakdown with UV light exposure.
- Available in an industry first ultra concentrate, 1 gallon of Lithi-Tek 4500 mixes with 2 gallons of water to make 3 gallons of sealer that will treat up to 1000 sq. ft. of concrete per coat.
Avoid contact with skin, eyes and clothing. Wash hands after use and do not take internally. Please refer to the product Safety Data Sheet (SDS) before using. The preparation process should be followed to ensure adequate penetration and optimum performance:
The concrete substrate must be structurally sound, thoroughly dry and clean. Wait at least 24-48 hours after rain and/or pressure washing before sealing; concrete should be visibly dry.
Remove all paints, previous sealers and/or adhesives before application.
The substrate must be clean of oil, grease, dirt, wax, curing compounds, efflorescence and other contaminants that might interfere with the penetration of the sealer.
If acid is used to clean the concrete, neutralize the surface completely and rinse it with water prior to application. Then wait for the concrete to dry out for at least 24-48 hours.
The surface-zone moisture content of the concrete should not exceed 4%wt.
Cover all surrounding areas not intended to be coated.
New concrete must be cured for at least 28 days before sealing.
Lithi-Tek® 4500 is a concentrated product that needs to be mixed with water prior to application. We recommend using a five (5) gallon bucket to mix the sealer. Pour the one (1) gallon container of Lithi-Tek® 4500 into a five (5) gallon bucket.
If densifying or priming concrete:
Next fill up the bucket with three (3) gallons of water (distilled water is preferred). (Lithi-Tek® 4500 can be mixed in smaller quantities as long as the one (1) part Lithi-Tek® 4500 to three (3) parts water ratio is followed. For example, one (1) cup Lithi-Tek® 4500 can be mixed with three (3) cups of water).
- If polishing concrete:
Next fill up the bucket with two (2) gallons of water (distilled water is preferred). (Lithi-Tek® 45000 can be mixed in smaller quantities as long as the one (1) part Lithi-Tek® 4500 to two (2) parts water ratio is followed. For example, one (1) cup Lithi-Tek® 4500 can be mixed with two (2) cups of water).
Stir the Lithi-Tek® 4500 and water mixture well before using.
If spray applying, pour the mixed material into a sprayer. If roll applying, dip a 3/8" nap roller into the bucket of mixed material.
Spray or roll one coat onto the application area. Apply until the surface is saturated but not to the point of puddling.
Roll or broom out any puddles until the sealer penetrates the substrate.
Let the concrete dry for at least six (6) hours before walking, 24 hours before driving, and protect the concrete from rain for at least 24-48 hours after sealing. Wait at least 7 days after applying the Lithi-Tek® 4500 before using a top coat sealer or paint.
Clean up: Application tools can be cleaned using soap and water.
If over-spray occurs it should be cleaned and removed immediately after sealing.
Unused or old material may be disposed of in a waste disposal site in accordance with local, state and federal laws.
- Before application test the sealer by applying in an inconspicuous area to ensure the desired coverage and appearance is achieved.
- Do not use on extremely porous concrete or masonry such a hollow concrete block or bricks.
- Do not over apply. Excess material may result in a white residue or discoloration.
- Prevent from getting on glazed and finished surfaces such as glass, aluminum etc. In case of contact flush immediately with water.
- Does not prevent equipment leaks or other leaks such as oil, hydraulic fluid etc. Use in conjunction with the Siloxa-Tek® 8505 or Siloxa-Tek® 8510 for oil repellency and staining resistance.
- Do not use on concrete that has been previously sealed without chemically etching or mechanically scarifying.
What is the difference between the Lithi-Tek 4500 and Sila-Tek 3500?
The Lithi-Tek 4500 is of a lithium silicate chemistry, whereas the Sila-Tek 3500 is of a sodium silicate chemistry.
What do you mix the concentrate with?
The Lithi-Tek 4500 concentrate is mixed with water. 1 gallon of Lithi-Tek 4500 is mixed with 2 gallons of water.
Can I paint after sealing?
Yes, you can paint after applying the Lithi-Tek 4500.
Does the concrete need to be dry before sealing?
Yes, the concrete needs to be as dry as possible before sealing. We recommend the moisture content of the concrete be less than 4%wt. It is recommended to wait at least 24-48 hours after rain and pressure washing before sealing.
My floor turned white after sealing, what happened?
This is a common result of over application. Once the concrete reaches its point of absorption any material that was unable to penetrate reacts with the carbon dioxide in the air. This reaction leaves a white, powdery residue on the surface of the concrete. This can easily be removed by sweeping the concrete with a wire brush.
Why cant I use this product on brick or concrete blocks?
This product is not recommended for use on brick because the Lithi-Tek 4500 is a penetrating, reactive sealer. Bricks do not contain enough free lime and calcium for the sealer to react with and this causes the bricks to dry with a white, powdery residure. This product is not recommended on concrete blocks because concrete blocks are extremely porous. The best product to seal bricks and concrete blocks is the Siloxa-Tek 8500.
How many gallons do I need to treat 1000 square feet?
You will need 1 gallons to treat 1000 square feet. Each concentrated gallon of Lithi-Tek 4500 will cover up to 1000 square feet.
What can I use to apply this product?
The Lithi-Tek 4500 can be applied with a garden variety pump sprayer, 3/8" nap paint roller or a brush.
How do I mix the product with water?
The Lithi-Tek 4500 is a concentrated product that needs to be mixed with water prior to application. Pour the 1 gallon of Lithi-Tek 4500 into a 5 gallon bucket. Next add 2 gallons of water into the 5 gallon bucket. Mix the water and 4500 mixture well. You can then pour the mixture into a sprayer to spray apply, or you can dip a nap paint roller into the bucket and roll apply.
How do I clean out the sprayer after sealing?
Since the Lithi-Tek 4500 is a water based product you can use regular soap and water to clean out the sprayer and other application tools.
Where can I buy this product?
The Lithi-Tek 4500 is available through a number of distributors found on our distributor page.