Supporting photo - Lithi-Tek 4500

Concrete: 50% Stronger

Super strength — unparalleled durability and toughness provided by freak science — where most superhero stories start. Let, it's the most advanced, lithium-based concrete densifier available, resulting in better abrasion resistance and crack prevention than sodium-based alternatives.

Penetrates Deep & Reduces Dusting

Easily applied with a sprayer, roller or brush, the 4500 can be used on a variety of poured concrete substrates. Can be used indoors and outdoors but a sealer is recommended to be used in conjunction if concrete will not be polished. A popular choice to prime and harden new and old concrete.

  • Primer for Siloxa-Tek 8500, Siloxa-Tek 8505 or Siloxa-Tek 8510
  • Warehouses / Industrial Facilities
  • Bricks
  • Concrete Blocks / Cinderblocks
  • Polished or Extremely Smooth Concrete
Supporting photo - Lithi-Tek 4500

Dries Invisible

Use stand-alone, as a primer for polishing, or as a primer for other Ghostshield sealers to increase adhesion. Provides a flat, natural finish. Dries within a few hours of application and requires only a single treatment.

Strengthens Concrete

Concept image for Strengthens Concrete

Resists Abrasion

Concept image for Resists Abrasion

Which is Best for You?

  • /product/lithi-tek-4500 Concrete Sealer Bottle Image
    Lithi-Tek 4500
    Protects Against
    Abrasion
    Formula
    Water-based
    Chemistry
    Lithium-Based
    In Stock
    Concentrated
    Current Product
  • 3500 Concrete Sealer Bottle Image
    Sila-Tek 3500
    Protects Against
    Abrasion
    Formula
    Water-based
    Chemistry
    Sodium-Based
    In Stock
    Concentrated

Product Details

    • 100% reactive- Densifies concrete surfaces into a solid mass by penetrating the concrete and chemically filing the pores from within reacting with the calcium hydroxide becoming an integral part of the concrete
    • Increases abrasion resistance by up to 50% - Tightly binds together concrete reducing concrete dusting. Provides ease of maintenance to provide long-lasting protection on substrates subject to traffic
    • Small molecular structure - Allows for deeper penetration and increased performance
    • Combats ASR attacks - Resists alkali-silica reaction
    • One-time permanent application eliminating the need for re-application
    • Increased performance of topcoat sealers when used as a densifying primer
    • Does not alter surface appearance - The treated surface is natural, tack-free and slip-resistant
    • Resists efflorescence
    • 100% Breathable - Allows moisture to escape without damaging the sealer
    • Water-based - Proprietary, environmentally friendly formula with no odor, no VOC’s
    • Excellent penetration depth into any concrete substrate
    • Improves durability - Increases impact resistance
    • Super UV stable - Resistant to ultra-violent radiation, will not yellow or fad
    • Concentrated - Makes up to 2 gallons
  • Surface Preparation

    1. New “green” concrete must be properly cured. Concrete should obtain 80% of design strength, typically achieved within 28 days.
    2. The concrete substrate must be structurally sound and clean of oil, grease, dirt, wax, curing compounds, efflorescence, paints, previous sealers, adhesives and other contaminants that might interfere with the penetration of the sealer. Power wash, acid etch or mechanically scarify as necessary to achieve the desired surface condition. If acid was used to clean the concrete, neutralize the surface and rinse with water prior to application. Allow for proper dry time before application. The surface-zone moisture content of the concrete should not exceed 4% wt. Do not apply if standing water is visible.
    3. Surface and air temperatures must be at least 40°F during application. Surface and air temperatures should not exceed 95°F. Do not apply when temperatures are expected to fall below 32°F within 8 hours or when rain is expected within 12 hours following application. Keep material from freezing. If freezing conditions exist before application, let the substrate thaw before application. Do not apply during inclement weather or when inclement weather is expected within 12 hours.
    4. Crack, patching and expansion joint sealants can be applied after application; always test for compatibility and adhesion.
    5. Protect people, property, vehicles, window glass, roofing materials, plastic products, shrubbery, landscaping and all surfaces not set for treatment from overspray.

    Application - Primer - Concentrate

    1. Always test a small area before application to ensure desired performance, aesthetics, coverage rates and to verify application technique. Let test area dry thoroughly, 5-7 days, before inspection.
    2. Always mix the concentrate with 1 parts water prior to application. Distilled water is recommended for maximum performance. Stir material throughly before and during application.
    3. One uniform coat is needed to ensure complete coverage. Apply with a roller, brush or low-pressure non-atomizing sprayer. Apply to saturation and roll or broom out any puddles until the sealer penetrates the substrate. Do not over apply. If applied too heavily, an unreacted white residue may develop on the surface. If it starts to rain, stop treatment and cover the treated areas.

    Application - Polishing - Ready to Use

    1. Always test a small area before application to ensure desired performance, aesthetics, coverage rates and to verify application technique. Let test area dry thoroughly, 5-7 days, before inspection. 2. Stir material throughly before and during application.
    2. One uniform coat is needed to ensure complete coverage. Apply with a roller, brush or low-pressure non-atomizing sprayer. Apply to saturation and roll or broom out any puddles until the sealer penetrates the substrate.

    Dry Time

    Typical drying time is 4-6 hours at 70°F and 50% relative humidity. Cooler temperatures or higher relative humidity can extend the drying time. Treated surfaces will be ready for pedestrian and vehicle traffic within 24 hours.

    Clean Up

    Clean equipment and tools with hot soapy water. Unused or old material may be disposed of in a waste disposal site in accordance with local, state and federal laws.

    Precautions/Safety

    Avoid contact with skin, eyes and clothing, do not take internally. Use appropriate safety equipment during application and handling. Please refer to the safety data sheet (SDS) for additional precautionary instructions before use.

    Best Performance

    • Proper application is the responsibility of the user.
    • Do not use on extremely porous concrete or masonry such as CMU block.
    • Do not over apply. Sealer is highly reactive. Excess material may result in a a white residue or discoloration on the surface.
    • Does not protect against equipment leaks such as oils and hydraulic fluids.
    • Make sure the most current versions of product data sheets and SDS are being used.

    Coverage

    Lithi-Tek® 4500 1 coat: 100 - 800 square feet. Variations in texture and porosity of substrate may affect the coverage and performance of the product.

  • What is the difference between the Lithi-Tek 4500 and Sila-Tek 3500? The Lithi-Tek 4500 is of a lithium silicate chemistry, whereas the Sila-Tek 3500 is of a sodium silicate chemistry.

    What do you mix the concentrate with? The Lithi-Tek 4500 concentrate is mixed with 1 part water if priming concrete. If polishing concrete the Lithi-Tek 4500 is ready to use, no mixing is required.

    Can I paint after sealing? Yes, you can paint after applying the Lithi-Tek 4500.

    Does the concrete need to be dry before sealing? Yes, the concrete needs to be as dry as possible before sealing. We recommend the moisture content of the concrete be less than 4%wt. It is recommended to wait at least 24-48 hours after rain and pressure washing before sealing.

    My floor turned white after sealing, what happened? This is a common result of over application. Once the concrete reaches its point of absorption any material that was unable to penetrate reacts with the carbon dioxide in the air. This reaction leaves a white, powdery residue on the surface of the concrete. This can easily be removed by sweeping the concrete with a wire brush.

    Why cant I use this product on brick or concrete blocks? This product is not recommended for use on brick because the Lithi-Tek 4500 is a penetrating, reactive sealer. Bricks do not contain enough free lime and calcium for the sealer to react with and this causes the bricks to dry with a white, powdery residure. This product is not recommended on concrete blocks because concrete blocks are extremely porous. The best product to seal bricks and concrete blocks is the Siloxa-Tek 8500.

    What can I use to apply this product? The Lithi-Tek 4500 can be applied with a garden variety pump sprayer, 3/8" nap paint roller or a brush.

    How do I mix the product with water? If priming concrete, the Lithi-Tek 4500 is a concentrated product that needs to be mixed with water prior to application. Pour the 1 gallon of Lithi-Tek 4500 into a 5 gallon bucket. Next add 1 gallon of water into the 5 gallon bucket. Mix the water and 4500 mixture well. You can then pour the mixture into a sprayer to spray apply, or you can dip a nap paint roller into the bucket and roll apply.

    How do I clean out the sprayer after sealing? Since the Lithi-Tek 4500 is a water based product you can use regular soap and water to clean out the sprayer and other application tools.

Product Reviews