Photo for Stamped concrete driveway sealed with a Ghostshield concrete sealer
8500 Concrete Sealer Bottle Image

Siloxa-Tek 8500

  • Water Repellent
  • Salt Repellent
  • Water-Based
  • Ready-to-use
  • Concentrated

The 8500 is the easiest to use and most versitle concrete sealer we offer. Best used on driveways in climates exposed to winter and freeze-thaw cycles providing protecion against water and deicing salts. Best used in basements to prevent moisture intrusion. Best used on patios to resist mold, midlew, efflorescence and water penetration.

The Siloxa-Tek 8500 is our favorite product to treat nearly any application. This concrete sealer can be used on a variety of substrates including concrete, brick, pavers, stamped concrete and exposed aggregate. The Siloxa-Tek 8500 is a water-based penetrating sealer that leaves a natural finish, meaning it will not change the look or appearance of the concrete.

The 8500 is used to protect driveways from deicing salts and mag chlorides. If concrete is left unsealed it can result in spalling, pitting and cracking. The Siloxa-Tek 8500 is able to resist deicing salt damage and keep concrete strong and waterproof. The 8500 is also used to treat basement floors and walls, paver patios, pool decks, chimneys and more.

Available in a ready to use version, or an ultra concentrated version. The ultra concentrated version makes 5 gallons and is mixed with 4 gallons of distilled water prior to application. Two coats are easily applied wet-on-wet (the second coat is applied immediately after the first coat while the first coat is still wet) with a sprayer, roller or brush.

To increase the strength and performance of the Siloxa-Tek 8500, apply one coat of the Lithi-Tek 4500 five to seven days prior to sealing with the Siloxa-Tek 8500.

The Micro-Degreaser 1100 can be used to degrease and remove soils and stains prior to using the Siloxa-Tek 8500.

Photo for
9500 Concrete Sealer Bottle Image

Lithi-Tek 9500

  • Water Repellent
  • Water-Based
  • Concentrated

A penetrating concrete densifier, hardener and waterproofer. Only used on poured concrete substrates to increase the strength and repel water

Commonly used on basements, driveways and patios, the 9500 is the most cost effective concrete sealer we offer. In basements the Lithi-Tek 9500 is best used on new concrete or used preventatively on concrete that has never had any moisture issues. On driveways and patios the Lithi-Tek 9500 is best used to repel water and resist mold and mildew growth.

Lithi-Tek 9500 can only be used on poured concrete substrates and concrete that has never been stained or dyed.

Lithi-Tek 9500 is concentrated, makes 5 gallons and needs to be mixed with distilled water prior to application. One part Lithi-Tek 9500 is mixed with 4 parts water. Two coats are applied wet-on-wet (the second coat is applied immediately after the first coat) with either a sprayer or roller.

Photo for
8510 Concrete Sealer Bottle Image

Siloxa-Tek 8510

  • Water Repellent
  • Oil Repellent
  • Salt Repellent
  • Solvent-Based
  • Ready-to-use

The Siloxa-Tek 8510 is our highest performing and longest lasting penetrating concrete sealer. Best used on concrete, brick or masonry to protect against water and resist deicing salts and staining from oils and greases.

The Siloxa-Tek 8510 the highest performing and longest lasting concrete sealer in the Siloxa-Tek line. This deep penetrating formula offers exceptional protection and a service life of up to 15 years. Thanks to a proprietary flurocarbon, this near 100% actives silane/siloxane blend is the only sealer capable of repelling water, deicing salts and motor oils. Its hydrophobic nature resists freeze-thaw damage, mold, mildew and moisture intrusion.

Available only in a ready to use version, two coats are easily applied wet-on-wet with a solvent rated sprayer, roller or brush. The concrete retains its natural, flat finish after sealing.

To increase the strength and performance of the Siloxa-Tek 8510, apply one coat of the Lithi-Tek 4500 five to seven days prior to sealing with the Siloxa-Tek 8510.

Photo for
8505 Concrete Sealer Bottle Image

Siloxa-Tek 8505

  • Water Repellent
  • Oil Repellent
  • Salt Repellent
  • Water-Based
  • Ready-to-use
  • Concentrated

The Siloxa-Tek 8505 is the water-based and low VOC version of the Siloxa-Tek 8510.

We took our favorite all-around, concrete sealer and made it even better. Take all the best attributes of 8500 - resists water intrusion, deicing salts and chlorides and add to it resistance from staining. The same stain resistance technology found in the 8510 is also in this water based product, making oil and grease clean up easier. The main difference between the 8510 and the 8505 is that the 8510 uses a solvent as a carrier and the 8505 uses water as a carrier.

Available in a ready to use version, or an ultra concentrated version. The ultra concentrated version makes 5 gallons and is mixed with 4 gallons of distilled water prior to application. Two coats are easily applied wet-on-wet with a sprayer, roller or brush.

To increase the strength and performance of the Siloxa-Tek 8505, apply one coat of the Lithi-Tek 4500 five to seven days prior to sealing with the Siloxa-Tek 8505. When used as a primer it reduces porosity, prevents cracking and surface deterioration and increases adhesion of a top coat sealer up to 25%.

Photo for Stamped concrete patio sealed with a high gloss, wet look concrete sealer by Ghostshield concrete sealers
5505 Concrete Sealer Bottle Image

Cryli-Tek 5505

  • Water Repellent
  • Solvent-Based
  • Ready-to-use

Best used where a high gloss or wet look finish is desired to enhance and darken the substrate.

When you are looking to bring out the colors and textures of a substate with a clear, non-yellowing finish the 5505 is an excellent choice. Since the 5505 is solvent based, it is the longest lasting sealer in the Cryli-Tek line. The 5505 can be applied to a substrate that has been previously sealed as long as the previous sealer was a solvent based acrylic. Keep in mind acrylic sealers do not last as long as penetrating sealers and may need to be reapplied more frequently.

One thin, even coat of the 5505 is applied with a 3/8” nap solvent rated high quality roller.

The 5505 may be slippery when wet. The Grip-Tek 250 slip resistant additive can be mixed in to the 5505 for added traction. If the wet look finish of the 5505 is too shiny the Matte-Tek 5000 may be added to reduce the gloss.

Photo for
5500 Concrete Sealer Bottle Image

Cryli-Tek 5500

  • Water Repellent
  • Water-Based
  • Ready-to-use

Best used where a low gloss, wet look finish is desired. This water-based acrylic sealer has a low odor and is easy to use.

We took all the best attributes of the 5505 - clear, non-yellowing, UV stable and made it into a low-gloss, wet look, water-based formulation. The acrylic resins used in this formula have been independently tested and are more durable and last longer than other acrylic sealers on the market. Protects and enhances the look of decorative surfaces for up to 3 years. Treated surfaces resist staining, surface deterioration and hot tire pickup while eliminating concrete dusting.

The 5500 is water based and VOC compliant in all 50 states making it a great option in areas with strict VOC laws.

One thin, even coat of the 5500 is applied with a 3/8” nap high quality roller.

Photo for
325 Concrete Sealer Bottle Image

Epoxy 325

  • Oil Repellent
  • Chemical Resistant
  • Water-Based
  • Two-component

Best used as a primer before using the Urethane 645 top coat. This durable epoxy floor coating repels chemicals, stops dusting and resists abrasions in a clear or colored semi-gloss finish

The Epoxy 325 is the first step in an epoxy floor coating system. This primer is applied after the concrete has been etched or grind-ed. Before applying an epoxy floor coating it is best to scarify and rough up the surface of the concrete in order for the coating to properly bond and adhere. This can be achieved by acid etching and neutralizing the concrete or by mechanically grinding the concrete with a floor grinder.

Once the surface has been properly prepped the Epoxy 325 can then be applied with an epoxy glide roller. The Epoxy 325 is available in a two component kit. Each kit contains a Part A and a Part B. Part A and Part B are mixed together with a drill or jiffy mixer. Once Part A and Part B are mixed the Epoxy 325 must be applied within 1 hour. About 7-10 hours after applying the Epoxy 325, the Urethane 645 can then be applied as a top coat.

The Epoxy 325 is available in clear or colored. If you are using a colored epoxy primer you are going to want to use the same color top coat. Paint chips (for decoration) or aluminum oxide (for slip resistance) can be cast into the wet epoxy and then top coated with the Urethane 645.

The combination of the Epoxy 325 primer and Urethane 645 top coat are excellent at stopping dusting, repelling oils, greases, chemicals and acids; however, they can only be used on indoor concrete floors.

If there is moisture in the concrete prior to application first use the Vapor-Tek 440.

The Micro-Degreaser 1100 can be used to degrease and remove soils and stains prior to using the Epoxy 325.

The Hydro-Etch 1000 can be used to etch the concrete prior to applying the Epoxy 325.

Photo for
645 Concrete Sealer Bottle Image

Urethane 645

  • Oil Repellent
  • Chemical Resistant
  • Solvent-Based
  • Two-component

Best used as a top coat after using the Epoxy 325 primer. This durable urethane floor coating repels chemicals, stops chemicals and resists abrasions in a clear or colored high-gloss finish

The Urethane 645 is typically applied about 7-10 hours after applying the Epoxy 325. If more than 48 hours have elapsed since the Epoxy 325 primer has been applied it is best to lightly sand the surface of the Epoxy 325 to maximize the bond and adhesion of the Urethane 645.

The Urethane 645 is also available clear or colored and in a two component kit. Each kit contains a Part A and a Part B. Part A and Part B are mixed together with a drill or jiffy mixer. Once Part A and Part B are mixed the Urethane 645 must be applied within 2 hours.

One coat of the Urethane 645 is best applied with an epoxy glide roller. The Urethane 645 leaves a high gloss finish and is extremely easy to clean. However, it can also be slippery when wet. If maximum traction is desired 46 Grit Aluminum Oxide can be cast into the wet Epoxy 325 and then coated with the Urethane 645. If lesser traction is desired a slip resistant additive can be mixed into a kit of Urethane 645.

The combination of the Epoxy 325 primer and Urethane 645 top coat are excellent at stopping dusting, repelling oils, greases, chemicals and acids; however, they can only be used on indoor concrete floors.

Because of VOC restrictions in the State of California, the Urethane 645 cannot be used. A California compliant version of the Urethane is available for use in California.

Photo for
4500 Concrete Sealer Bottle Image

Lithi-Tek 4500

  • Water-Based
  • Concentrated

Best used as a primer before using a concrete sealer or during the concrete floor polishing process if a polished concrete floor finish is desired.

The Lithi-Tek 4500 is a penetrating lithium silicate based concrete densifier that can make concrete up to 50% stronger. Lithium based silicates penetrate deeper and work better than traditional sodium silicate based densifiers. The 4500 can also be used as a primer on poured concrete substrates before using a concrete sealer. In addition to making the concrete stronger, the 4500 acts as a bonding agent to increase the adhesion of the subsequent sealer. The 4500 also makes concrete less porous and works great when used in conjunction with a water repellent sealer.

By using the 4500 prior to polishing concrete it will make the concrete harder and will give it more of a shine to resist stains and water damage. If concrete densifier is not used during the polishing process the concrete can wear faster and lose its shine quicker.

Lithi-Tek 4500 is concentrated and needs to be mixed with distilled water prior to application. One part Lithi-Tek 4500 is mixed with 3 parts water. One coat is applied with either a sprayer or roller.

Photo for
440 Concrete Sealer Bottle Image

Vapor-Tek 440

  • 100% Actives
  • Two-component

Best used on concrete floors with a high moisture content (up to 20lbs/24hr/1000ft) or prior to installing wood, carpet, tile or epoxy flooring

If the concrete basement floor has a high moisture content the Vapor-Tek 440 is the product to use. This two-component epoxy coating is designed to reduce moisture vapor emission rates of up to 20lb/24hr/1000ft. If you are going to be installing carpet, tile or wood this is the product to use to prevent any moisture from traveling and dis-bonding the flooring. It is also an excellent choice to use the Vapor-Tek 440 as a primer before installing an epoxy floor.

Each gallon will cover up to 100 square feet at 17 mils thickness and will leave a clear, gloss finish. Part A is mixed with Part B prior to application and installed with an epoxy glide roller. The Vapor-Tek 440 will stop dusting, can be applied to concrete as little as 10 days old and only requires one coat.

The Vapor-Tek 440 does have a short pot life which means once Part A and Part B are mixed together it needs to be applied within 30-40 minutes. Once the pot life has been reached the product can no longer be applied. The Vapor-Tek 440 is dry and ready for foot traffic within 24 hours and fully cured in 3-7 days.

Photo for
1505 Concrete Sealer Bottle Image

Pro-Fusion 1505

  • Water-Based
  • Ready-to-use

A water-based, solid color concrete stain system featuring a solid color stain, optional primer and optional enhancer.

When you are looking to add a solid color gloss finish to a substate, the 1505 is an excellent choice. Since the 1505 is water based, it is completely safe to use with no odor. It locks color deep below the surface, hiding imperfections to make surfaces look beautiful, even, and consistent in appearance. It is capable of providing a uniform color or enhanced “mottled” color look on stamped concrete.

The Pro-Fusion 1505 can be used as a stand alone stain, or as part of a system.

Optional Step 1: If the substrate is extremely old or porous use the Pro-Fusion 1505 Primer first.

Required Step 2: Pro-Fusion 1505 available in 6 standard colors: Tan, Dark Tan, Medium Gray, Dark Gray, Brown, Dark Red

Optional Step 3: If you are looking for additional enhancement and depth especially on stamped concrete to highlight groves and patterns use the Pro-Fusion 1505 Enhancer after using the Pro-Fusion 1505 Stain. Available in 3 standard colors: Chocolate, Charcoal, Mocha

The Cryli-Tek 5500 is always recommeded as the top coat sealer for added UV protection and longevity.

Photo for Stamped concrete patio sealed with Ghostshield Wear-Tek 4400 concrete sealer
1500 Concrete Sealer Bottle Image

Hydro-Stain 1500

  • Water-Based
  • Concentrated

A water based, translucent concrete stain that can safely achieve acid like effects.

This unique formula is a safe alternative to acid-based stains containing no hazardous components while producing the same mottled look as acid stains. There is no neutralizing or rinsing required. The product is shipped concentrated and mixed with water prior to application.

Provides a flat, natural finish. Can be applied at full strength or diluted with water for a lighter color. Colors can also be mixed and applied in random patterns. Available in 6 standard colors. A decorative sealer like the Cryli-Tek 5505 is recommended after staining to ensure long lasting protection and color enhancement.

Photo for
745 Concrete Sealer Bottle Image

Polyaspartic 745

  • Water Repellent
  • Oil Repellent
  • Chemical Resistant
  • Solvent-Based
  • Two-component

The longest lasting and best performing countertop sealer we offer. This high gloss, wet look formula is able to withstand food stains, spills, chemicals and abrasions.

The Polyaspartic 745 is typically used in commercial kitchens and bars since it is the most durable countertop sealer available. The Polyaspartic 745 can also be used on warehouse floors and is able to stand up to forklift traffic, chemicals and abrasions so using it on a concrete countertop is a no brainer. The 745 can only be used on interior concrete countertops and leaves the surface with a high gloss finish.

Since it is a coating rather than a sealer it sits on top of the concrete providing a smooth surface environment that allows for easy clean up and completely stops anything from penetrating through it.

Before applying the 745 we recommend sanding the concrete countertop with a 220 grit pad to ensure the surface has enough porosity for the coating to adhere to. The Polyaspartic 745 is sold in a 2 part kit, so you need to mix Part A with Part B. It has a short workable life, which means once you mix Part A with Part B you have about 15 minutes to apply it before it begins to harden and is unworkable.

You do need to let the countertop dry for at least a full 24 hours before use. Once cured you are left with an extremely durable, high gloss concrete countertop.

Photo for
660 Concrete Sealer Bottle Image

Countertop 660

  • Water Repellent
  • Water-Based
  • Concentrated

If you are looking for a little bit of shine that is not overly glossy but still able provide protection from light spills, use this product

If you are looking for a low sheen finish on your concrete countertops that is not as glossy as the 745 but not as flat as the 880, the 660 is an excellent option. Especially since is completely non-toxic, water-based and safe for interaction with food once cured.

The Countertop Sealer 660 is easy to apply; simply mix the concentrated solution with equal parts water and spread the solution over the countertop with a rag for five minutes. Continuously make sure the countertop is wet for the whole five minutes, then let the sealer completely penetrate into the concrete without wiping it up. After the surface has dried, apply another coat at a 3:1 ratio of sealer to water, which will help fully protect your countertops.

Use in conjunction with a countertop wax for an extra layer or protection.

Photo for
880 Concrete Sealer Bottle Image

Countertop 880

  • Water Repellent
  • Solvent-Based
  • Ready-to-use

Use this product if you do not want to the change the look or feel of the countertop but need protection from water and light spills. Since it is a solvent carried product it will outperform the 770.

The Countertop Sealer 880 is a solvent-carried food safe (once cured) sealer that will not change the look or appearance of the concrete countertop whatsoever. The 880 leaves a similar finish to the 770; however, its high actives content, ease of application, deeper penetration and longer lifespan set it apart.

The 880 is able to resist light staining from household substances causing fluids to sit on top of the concrete rather than penetrating into the concrete giving you a few extra minutes time to wipe up the spill.

The Countertop Sealer 880 is easy to apply and is ready to use right out of the container - no mixing is required. Two coats wet-on-wet (immediately apply a second coat while the first coat is still wet) are recommended.

Use in conjunction with a countertop wax for an extra layer or protection.

Planning a Project?
Start Here

Product Finder